A white Tesla-branded power electronics enclosure with a mesh-fronted panel, shown against a dark backdrop, illustrating the Tesla Powercore solid-state platform.

Tesla Powercore puts the conversion work of an inverter, transformer and breaker into a single medium-voltage unit

(Image courtesy of Tesla)

Tesla Powercore is a solid-state medium-voltage platform that combines a transformer, breaker and inverter in one enclosure. It converts battery DC straight to medium-voltage AC in a single stage, without a separate step-up transformer, and serves utility-scale solar and native 800 Vdc data centres. Powercore is rated for up to 9 MVA (7.4 MW) continuously at 34.5 kVac, with first units due to operate in 2027.

Tesla Powercore and single-stage conversion

At a Megapack site today, inverters inside the Megapack turn battery DC into 480 V AC before a separate transformer lifts it to medium voltage. Powercore converts directly from battery DC to medium-voltage AC in a single stage and is close-coupled with Megapack, and the two arrive pre-assembled. Tesla says the earlier architecture carried twice the losses, and that cutting them raises site energy density and lowers cost.

Across the platform, nominal DC runs from 800 V to 2,000 V and nominal AC from 10 kV to 34.5 kV, with a 10 MVA peak rating for grid-forming operation. Peak efficiency is 98.86%, the operating range is −40°C to 55°C, and system availability guarantees start at 99.9% alongside a bankable warranty of up to 25 years.

The built-in medium-voltage solid-state breaker clears faults up to 1,000 times faster than a conventional breaker, significantly reducing fault energy, and Tesla told pv magazine USA the clearing time is 100 microseconds. Because the design is modular, components can be serviced in the field without replacing the whole unit, and Powercore contains no flammable oil.

Powercore draws on lessons from the Megapack 2XL. Tesla reports that the 2XL is operating at 99.73% average annual availability across more than 50 GWh as of Q3 2026, and that with Powerhub, which monitors sites and acts as the power plant controller, the whole battery site can be standardised with no third-party equipment.

Tesla Powercore for 800 Vdc data centres

In 800 Vdc data centres, Tesla positions Powercore as the power supply for both the infrastructure and the compute, in place of a chain in which most equipment takes 415 to 480 Vac input, relies on medium-voltage transformers and redundant equipment, and converts power again for cooling, networking and compute. Tesla Powercore goes from the medium-voltage feeder straight to 800 Vdc in one step. NVIDIA, Google and Microsoft are working through the Open Compute Project to establish 800 Vdc as a standardised power architecture, and NVIDIA’s architecture supports direct medium-voltage AC to 800 Vdc conversion for future AI factories.

Tesla says built-in redundancy gives up to 99.7% product-level availability, reducing the equipment needed to reach five nines at the system level, and that lower conversion losses put more GPUs online on the same interconnected power. Powercore can sit directly on the DC bus with Megapack for backup and load smoothing, and 10 GWh of Megapack is already operating at data centres.

Tesla is collaborating with NVIDIA on engineering for 800 Vdc architectures and working to certify Powercore into the DSX Ready Program. Megapack is already qualified under the program, one of three battery energy storage solutions qualified at launch alongside Hitachi Energy and LG Energy Solution. Paired with Megapack, Powercore uses Tesla’s grid-forming controls to provide synthetic inertia and reactive power support, and AJ Booth, Tesla’s head of energy and charging, said managing a data centre’s dynamic loads this way can steady local voltage and the wider grid.

Tesla Powercore in utility-scale solar

For solar, Tesla Powercore works as a central PV inverter that converts array DC directly to medium-voltage AC with less equipment, supporting the 1,500 Vdc systems in the field today and emerging 2,000 Vdc designs. Tesla says transformer supply constraints are holding new plants back and inverter downtime is the leading cause of lost availability, while pv magazine USA reports transformer lead times of as long as four years.

Powercore’s first units are due to operate in 2027, the year NVIDIA’s roadmap has full-scale production of 800 Vdc data centres arriving alongside its Kyber rack-scale systems. Tesla will build it in the United States from US and imported parts and is presenting it at RE+ 2026 in the Las Vegas Convention Center.

Stay ahead in the electrification revolution. Explore more breakthroughs from leading innovators in electric commercial transport – visit our news page.